clapgeek logo
In PTN, LSP is created statically. Which items are correct in the following description about LSP creation?
The multi-level connection monitoring mode (TCM) of OTN has three application forms. Which of the following is correct?
Which of the following descriptions about the PTN network deployment ring network intersecting ring are correct?
Which of the following conditions will cause multiple channels to report BEFFEC-EXC alarms at the same time?
Which of the following bridges are used to forward data based on the MAC address and VLAN ID carried in the data?
What are the possible reasons for the unsuccessful OCH creation by the path method?
The EDFA erbium-doped fiber amplifier is a key component of the new generation of optical fiber systems. Which of the following options are correct for the description of its advantages?
Standard Ethernet frame length should not be less than 64 bytes. Which of the following factors would cause this limitation?
Which of the following items can be included in the upgradeable boards of the PTN3900 NE upgrade operation?
Which of the following statements about the slave subrack SCC function is correct?
The characteristic of the open DWDM system is that there are no special requirements for the optical interface of the multiplexing terminal, and only these interfaces are required to comply with the optical interface standard
recommended by ITU-T. The DWDM system adopts wavelength conversion technology to convert the optical signal of the multiplexed terminal into a specific wavelength, and the optical signal of different terminal equipment is converted into
different wavelengths that comply with ITU-T recommendations, and then multiplexed.
In order to support the self-opening of the base station and deploy the DHCP Relay function in the PTN LTE bearer network, which one of the following descriptions is wrong?
In the CES service, which of the descriptions of "packet loading time" and "jitter buffer time" is wrong?
When the device reports the PW_APS_DEGRADED alarm, what is the problem with the LTE service carried by the station?
In the current network, which of the following is the most common way of dividing VUNs?
In the MPLS-TPOAM architecture of PTN equipment, what are the functions of network performance maintenance?
According to the deployment plan of the existing network, which protocol does not need to be deployed for the interconnection between PTN equipment and SGW
Which one of the following is not necessary to establish a GE-level service path on the network management?
According to the deployment plan of the existing network, which protocol does not need to be deployed for the interconnection between PTN equipment and SGW?
When the bridge is using ML learning mode, create an entry in the MAC.Address gateway depending on the source MAC map and server port. This entry applies to all VANs
The L3VPN routing of the PTN LTE network includes user-side routing and network-side routing. What are the items based on which VPN routing forwarding table is finally generated?
Which of the following item levels are included in the MPLS-TP OAM detection object?
Standard FEC, AFEC and HFEC techniques all increase the FEC overhead, and the coding gains achieved are progressively increased.
Which of the following descriptions about the Optix OSN 9800 subrack are correct?
Create an ETH private line service in the PTN network, and connect an Ethernet tester to the UNI port for RFC2544 testing. The instrument shows that the current port has only sending traffic
and no receiving traffic. What are the possible reasons?
When the data is forwarded by the PTN device, when the value of the TYPE field of the Ethernet header is 8847, what protocol is the inner packet of the encapsulation?
During the negotiation between the two ends of the PTN LAG, the device with the smaller system priority number is the master device
OptiX OSN 6800 supports centralized crossover and distributed crossover. When two kinds of crossovers exist, the system prefers to use centralized crossover
When performing single-site commissioning of SDH equipment, it is necessary to check the single-site hardware: including cabinet and subrack installation inspection, power line resistance measurement, cable layout specification
inspection, single-board appearance inspection, and some single-board inspections. DIP jumper check
If the E1 interface board D75S is not plugged into the OSN3500 hardware, the indicator on PQ1 will light up red
Which of the following is the electric layer particle that can be crossed by the TSXL veneer?
When deploying LAG, which of the following can the traffic load sharing hash algorithm be based on?
Which of the following descriptions about bit errors in the SDH network is wrong?
Which of the following residual dispersion values are within the dispersion tolerance of the TN52ND2 board?
The international professional organization responsible for allocating P addresses has divided several network segments as private network segments, which can be freely allocated and used by people on the private network. What are the
following network segments belonging to private addresses?
Which of the following is the destination MAC address of the Layer 2 header of the data received by the PTN960 from the LTE base station?
In order to determine whether the optical fiber lines and connectors on the wavelength division side are normal, which of the following loopback methods is most suitable?
When creating a PTN tunnel, you can set the priority of the tunnel. There are 0, 1, and 7. The larger the value, the higher the priority.
The activation operation is successful in the PTN network element upgrade operation. Which of the following states is the network element in?
TESTED 21 Nov 2024