clapgeek logo
Which two tools can be used to actively monitor ONTAP cluster performance? (Choose two.)
Which NetApp solution enables block-level backup and restore from ONTAP to StorageGRID?
In a synchronous SnapMirror configuration, the soui'ce storage appliance exhibits high latency due to user traffic and rapid data change from SnapMirror transactions.Which one of the following tuning methods best resolves this performance behavior? Edit the /etc/snapmirror.conf file on the destination storage appliance and set:
A SnapVault secondary volume can contain up to ______________ Snapshot copies for data protection.
Open System SnapVault agents can be installed on all non-Network Appliance platforms.
You cannot disable the SyncMirror license if one or more mirrored volumes exist.
Which two Interfaces can an administrator use to disable unused Ethernet ports on an ONTAP cluster? (Choose two.)
If the local node has its FC HBA connected to switch Bank 1, it owns the disks connected to switch bank
What is the maximum number of disk shelves per loop in a fabric-attached MetroCluster?
Refer to the exhibit.
Based on the CPU headroom statistics provided for one node in the cluster, what is the available performance capacity?
SnapVaulr snapshots for SnapLock volumes are deleted automatically according to the retention count set in the SnapVault schedule?
Fill in the blank for the following statement: To manage a SnapVault backup through a commercial NDMP application, you must specify a_____authorized through that application.
The Snap Vault secondary system makes a snapshot of its own volume where the qtrees are located.
An administrator Is troubleshooting failed cluster peering between three ONTAP clusters for cascaded SnapMirror replication. Cluster1 is peered to Cluster, cluster^ is peered to Cluster3.
Clusterl and Cluster3 do not have an available route to reach each other. Cluster2 can route to both Cluster1 and Cluster3 using dedicated and separate intercluster LIFs.
What ONTAP network component must be configured on Cluster2 to resolve this issue?
When cabling a standard storage appliance for SyncMirror. disk pool 1 volumes must be cabled to Fibre Channel adapter(s) located in what range of slots on the FAS960 appliance?
Which one of the following /etc/snapmirror.conf entries will not support synchronous SnapMirror?
Which one of the following commands or procedures would you use to undo a SnapRestore reversion?
Which MetroCluster configuration procedure is recommended for re-establishing a mirrored volume that was in a level-0 re synchronization state when it failed?
Which capacity and parity savings feature is configured at the factory with all AFF systems?
Which ONTAP feature will allow WORM and non-WORM volumes in the same aggregate?
When using SAN protocols, what is the maximum number of nodes that can be added to a four node cluster?
Which native ONTAP feature allows an administrator to block a Windows user from writing files with the.crypto extension?
The required hardware to add SyncMirror to an existing Clustered Failover system consists of:
Which SyncMirror command mirrors an existing unmirrored aggregate where Data ONTAP selects the disk drives?
Which Data ONTAP option would you enable to set system wide throttling for all transfers?
Fill in the blank for the following statement: To manage a SnapVault backup through a commercial NDMP application, you must specify a_____authorized through that application.
An administrator wants to present datastores to a VMware environment that is using VLAN-10 and creates an SVM with NFS enabled on lif_NFS.
What does the administrator need to correct?
Which one of the following SyncMirror commands would you use to mirror an existing unmirrored volume where Data ONTAP selects the disk drives?
When configuring SyncMirror disk pools, which platforms require disks connected to particular ports and/or FC adapters on particular ports?
You can avoid data corruption when you issue the cf forcetakeover-d command if the remote node is
You want to create an automated test environment that performs a single file SnapRestore. Every time you run the procedure, however, SnapRestore prompts you to confirm your decision to revert the file. How can you automate this step?
Which one of the following options will allow a snapmirror storage appliance to mirror from this system?
You are trying to do a single file SnapRestore for a file, but you are receiving an error message that the directory structure no longer exists. Which one of the following is the most likely explanation?
What are two ways that an administrator can define a new consistency group? (Choose two.)
Exhibit.
An administrator has a NetApp AFF cluster with Cloud Tiering enabled on all data using the snapshot-only policy. When restoring files, users report slow response times.
What is the highest latency seen during restore?
Identify the two SnapMirror commands that are entered on the source storage appliance.
Due to the sensitive nature of AutoSupport messages, what transport protocol should a storage administrator configure?
Which command disables client access to Snapshot copies on a volume called flexvol1?
TESTED 03 Apr 2025